Packing Set

SKU:
F26
This sealing device is used to prevent solution from leaking into the interior cabinet. Refer to A200 Service Procedure 4 or ANKOM Packing Installation Part 1 for installation procedure.
$65.00

Brass Packing Nut 7/8/20

SKU:
640
This nut is used to tighten the packing to prevent leaking.
$15.00

Open End 1-1/8" Wrench

SKU:
Z557
This wrench is used with packing nut part # 640.
$11.00

Bag Suspender Tray (bottom)

SKU:
693

This is the bottom tray in the Bag Suspender.

New Bag Suspender design –  Ongoing research on the bag suspender suggested a higher degree of level to level variation for some sample types.  This led us to develop a new design that would do a better job of controlling the vertical flow to make sure the flow rate is basically the same at each level.  This new design is now being shipped with all new DELTA and A200 series fiber analyzers.

If you are planning to order replacement trays for your fiber analyzer with the original design we highly recommend switching to the new design.  Where required, we can provide the old design, but you will need to contact us by phone or email to confirm availability.

You CANNOT mix and match the “old” and new style bag suspender trays.

There is no change in pricing for the new design.  The new bag suspender will increase precision on a level to level basis for some sample types.

$26.00

Bag Suspender Tray (top)

SKU:
694

This is the top tray in the Bag Suspender.

New Bag Suspender design –  Ongoing research on the bag suspender suggested a higher degree of level to level variation for some sample types.  This led us to develop a new design that would do a better job of controlling the vertical flow to make sure the flow rate is basically the same at each level.  This new design is now being shipped with all new DELTA and A200 series fiber analyzers.

If you are planning to order replacement trays for your fiber analyzer with the original design we highly recommend switching to the new design.  Where required, we can provide the old design, but you will need to contact us by phone or email to confirm availability.

You CANNOT mix and match the “old” and new style bag suspender trays.

There is no change in pricing for the new design.  The new bag suspender will increase precision on a level to level basis for some sample types.

$21.00

Bag Suspender w/ weight

SKU:
F11

This assembly includes the Bag Suspender and the weight.

New Bag Suspender design –  Ongoing research on the bag suspender suggested a higher degree of level to level variation for some sample types.  This led us to develop a new design that would do a better job of controlling the vertical flow to make sure the flow rate is basically the same at each level.  This new design is now being shipped with all new DELTA and A200 series fiber analyzers.

If you are planning to order replacement trays for your fiber analyzer with the original design we highly recommend switching to the new design.  Where required, we can provide the old design, but you will need to contact us by phone or email to confirm availability.

You CANNOT mix and match the “old” and new style bag suspender trays.

There is no change in pricing for the new design.  The new bag suspender will increase precision on a level to level basis for some sample types.

$259.00

Bag Weigh Holder

SKU:
101.2
The 101.2 Bag Weigh Holder is used to hold a filter bag open for easy insertion of the sample.
This part is especially useful during the weighing process.
$14.00

Desiccant/Moisture Stop Assembly

SKU:
X45
Inside the zipper bag are desiccant packs that absorb moisture within the bag.
To avoid negatively impacting your assay results with unwanted moisture, use these assemblies to store filter bags while they are cooling after being dried.
$9.00

Agitate Switch Assembly

SKU:
F19
This switch turns the agitation to the digestion vessel on and off.
$62.00

Agitator Apron

SKU:
638.7
This apron funnels fluid into the maintenance alert assembly.
$13.00

Agitator w/ Packing Set

SKU:
F28
The agitator moves the bag suspender up and down creating correct flow of solvent in and out of the filter bags during digestion. The packing set prevents the solution from leaking into the interior of the instrument. Refer to A200 Service Procedure 4 or ANKOM Packing Installation Part 1 for installation procedure.
$308.00

Bag Suspender Rod w/ Nut Assembly

SKU:
F12.5
The F12.5 assembly is used in the ANKOM DELTA and A200 fiber instruments.
This hardware is used to hold the digestion trays in place during instrument operation.
$44.00

Bag Weight Machined

SKU:
639.1
The filter bags and trays are made of materials that will float in the detergent solutions used during fiber analyses.
The 639.1 weight is placed on the bag suspender to hold the trays in place during the digestion process in the ANKOM DELTA and A200 fiber instruments.
$30.00

Bolt Shoulder

SKU:
603
This bolt is used for securing the lid and hinge block assembly to the vessel.
$6.00

Brass Packing Nut (old)

SKU:
640.2
This nut is used to tighten the packing to prevent leaking.
$16.00

Breaker 8 amp (220v)

SKU:
617
This resettable breaker is used to protect the instrument against power surges that are out-of-specification.
$13.00

Check Sample - Alfalfa

SKU:
A100
This sample is to be used with the ANKOM DELTA/DELTAI and A200/A200I Fiber Analyzers.  The purpose of the check sample is both to ensure proper function of the instrument and correct procedural technique.  If your results do not meet the expected range, first check your procedural steps.  If the method has been followed properly, contact ANKOM Technology at [email protected] or call 1-315-986-8090.
 
$25.00

Controller Assembly

SKU:
F29
This assembly controls the heat to the digestion vessel.
$413.00

Coupler Helical (for Motor and Agitator)

SKU:
632
This part connects the motor to the agitator.
$35.00

Drip Tray

SKU:
692
This tray is used to collect fluid if a leak occurs.
$7.00

ETS Snap Disc

SKU:
622
This device protects the instrument from over temperature conditions.
$33.00

Exhaust Valve Assembly

SKU:
F2.3
Replacement exhaust valve for A200 / A200I Fiber Analyzer.  For replacement instructions refer to Service Procedure FS009.     
  

Related Documents: 
Procedure Title Download
09 Exhaust Valve Replacement (F2.3) View PDF
$129.00

Fan Blade

SKU:
6041
This fan keeps the motor cool during operation.
$7.00

Fuse 120v Assembly

SKU:
F16
This part protects the 120v instrument against power surges that are out-of-specification.
$21.00

Fuse 15 amp

SKU:
687
This fuse helps to protect the instrument from a surge in power.     
  
 
$3.00

Heat Switch Assembly

SKU:
F18
This switch turns the heat to the digestion vessel on and off.
$62.00

Heating Band Assembly 220v

SKU:
F10
This assembly heats the digestion vessel in the 220v instrument.
$138.00

Heating Band Fiber Assembly 120v

SKU:
F9
This assembly heats the digestion vessel in the 120v instrument.
$142.00

Hinge Block Assembly

SKU:
F3
This assembly connects the lid to the vessel.
$51.00

Hose Coupler 2 pc

SKU:
714
This coupler connects the drain exhaust hose to the DELTA.
$9.00

Inner Exhaust Hose Assembly (includes hose with clips)

SKU:
F30
This hose carries waste from the vessel to the outer exhaust hose.
$14.00

Kynar Tip w/ washer Assembly

SKU:
F11.5
This important part of the bag suspender regulates the amount of agitation in the digestion chamber.
$20.00

Lamp (Light Bulb)

SKU:
704
These lamps light the inside of heat and agitate switches.
$9.00

Lid Assembly

SKU:
F4
This lid seals the digestion vessel (F3 Hinge Block Assembly included).
$228.00

Lid Handle Assembly

SKU:
F4.8
This assembly includes the handle and clamping device used for sealing the lid and hinge block assembly to the vessel.
$29.00

Lid O-Ring Assembly

SKU:
F4.5
This assembly includes the O-ring used to seal the digestion vessel along with glue to secure the O-ring.
$29.00

Maintenance Alert Inner Assembly

SKU:
F27
To protect the interior of the instrument, this collection chamber catches fluid in the event of an internal leak.
$27.00

Maintenance Alert Outer Assembly

SKU:
F27.5
This assembly shows if the packing has started to leak.
$25.00

Motor Fiber Assembly 120v

SKU:
F7
This motor agitates the bag suspender at the proper RPM in the 120v instrument.
$175.00

Motor Fiber Assembly 220v

SKU:
F8
This motor agitates the bag suspender at the proper RPM in the 220v instrument.
$196.00

On/Off Power Switch (A200,A200I)

SKU:
691
This switch turns power on and off to the instrument.
$21.00

Outer Exhaust Hose Assy

SKU:
F12
This assembly removes waste from the digestion vessel.
$46.00

Pressure Switch Assembly

SKU:
F13
This assembly connects the pressure switch to the digestion vessel.
$63.00

Relay 120v

SKU:
629
This relay turns the heat source on and off.
$81.00

Relay 220v

SKU:
630
This relay turns the heat source on and off.
$76.00

Temperature Probe Assembly

SKU:
F1
This assembly includes a probe that provides an accurate temperature to the Athena controller.
$91.00

Timer Assembly

SKU:
F17
This timer controls the digestion time.
$50.00

Voltage Transformer 110v-220v

SKU:
6227
This transformer is used to step up or down the voltage needed for a device.

Since ANKOM provides a 110v Water Heater, this transformer is needed if you have 220v connections.
  
 
$200.00

Water Heater Assembly 120v

SKU:
A02
This water heater provides the correct rinse temperatures for DELTA operation. Refer to A2000 Service Procedure 18.

If you have a 220v connection, you will need to connect your water heater to a Voltage Transformer like part # 6227 (sold separately).
 
$595.00