Bag Weigh Holder

SKU:
101.2
The 101.2 Bag Weigh Holder is used to hold a filter bag open for easy insertion of the sample.
This part is especially useful during the weighing process.
$14.00

ANKOM RD Dryer, 120v

SKU:
RD
Residual acid left in the samples after the hydrolysis step can cause corrosion in a lab oven.
The ANKOM RD Dryer 120v 50/60 HZ with its acid absorbing filter is designed to dry the samples and resist corrosion.
Related Documents: 
Procedure Title Download
Info Sheet ANKOM RD Dryer Info Sheet View PDF
$2,230.00

ANKOM RD Dryer, 220v

SKU:
RDI
Residual acid left in the samples after the hydrolysis step can cause corrosion in a lab oven.
The ANKOM RD Dryer 220v 50/60 HZ with its acid absorbing filter is designed to dry the samples and resist corrosion.
Related Documents: 
Procedure Title Download
Info Sheet ANKOM RD Dryer Info Sheet View PDF
$2,230.00

Check Sample- Hydrolysis Sample

SKU:
H103
This sample is to be used with our HCL instrument. The purpose of the check sample is both to ensure proper function of the instrument and correct procedural technique. If your results do not meet the expected range, first check your procedural steps. If the method has been followed properly, please contact ANKOM Technology at [email protected]
$25.00

Drain Valve Assembly

SKU:
H5
This valve controls the drain operation.
$385.00

Dryer Activated Carbon Filter

SKU:
RD1
Located on the top of the dryer, this filter is used when drying filter bags before and after a fat extraction done with an ANKOMXT10 or an ANKOMXT15 Extractor.
$120.00

Dryer HCL Filter

SKU:
RD2
Located on the top of the dryer, this filter is used when drying filter bags after a hydrolysis operation is done with an ANKOMHCI Hydrolysis System.
$146.00

Fuse 10amp Short 120v

SKU:
206
This is a replacement 10amp fuse for a 120v instrument.
$3.00

Fuse Holder

SKU:
6110
Replacement Fuse Holder for ¼" x 1¼" fuse.
Fuses are ordered separately as part 687 (15A for A2000) or part 6035 (10A for A2000I).     
  

$4.00

Fuse Short 220v

SKU:
5578
This is a replacement fuse for a 220v instrument.
$4.00

HCL Bag Holder (15 Position)

SKU:
H37
The H37 Bag Holder is used to hold the bags in the HCL Extraction Chamber during as assay.
This assembly holds 15 bags.
$49.00

HCL Bag Holder (20 Position)

SKU:
H33
The H33 Bag Holder is used to hold the bags in the HCL Extraction Chamber during as assay.
This assembly holds 20 bags.
$50.00

HCL Blotter

SKU:
H35
Ideally you want to remove as much acid as possible from samples before drying them.
When using the blotter, you can remove a maximum amount of acid from the samples after completing the HCL extraction, and before drying in the dryer.
$120.00

HCL Lid Assembly

SKU:
H3
The HCL Extraction Chamber must be sealed during an assay.
The H3 lid seals the Extraction Chamber in the HCL instrument.
This assembly does not include the latch that secures the lid to the instrument.
$143.00

HCL Lid/Latch Assembly

SKU:
H2
The HCL Extraction Chamber must be sealed during an assay.
The H2 Lid/Latch Assembly seals the Extraction Chamber in the HCL instrument.
​This assembly includes the latch that secures the lid to the instrument.
$805.00

HCL Splat Controller Assembly

SKU:
H12
This is the internal computer that controls the HCL instrument.
$400.00

HCL Water Supply Valve Assembly

SKU:
H4
The H4 valve is a replacement Water Supply Valve for the HCL/HCLI.
Refer to Service Procedure HS003 for installation instructions. 
Related Documents: 
Procedure Title Download
03 Water Supply Valve Installation (H4) View PDF
$260.00

HCL Zinc Filter Assembly

SKU:
H36
Connected to the vent hose, this filter is used to capture any HCL vapors.
$49.00

Heater Cartridge Assembly 120v

SKU:
H31
This assembly heats the Extraction Chamber of the 120v instrument.
$97.00

Heater Cartridge Assembly 220v

SKU:
H34
This assembly heats the Extraction Chamber of the 220v instrument.
$106.00

Power Supply

SKU:
963
This 120/220 volt supply provides the correct power to the instrument electronics.
$196.00

Power Switch (A2000/A2000I, HCL/HCLI, RD/RDI, TDF/TDFI, XT10/XT10I, XT15/XT15I) & Heat Rotate Switch (D200/D200I)

SKU:
5653
For non-DaisyII instruments: This is a replacement On/Off Power Switch.

For the DaisyII Instrument: This is used for both heater and jar rotation motor.  Refer to Service Procedure DS005. 
Related Documents: 
Procedure Title Download
05 Wiring Diagram View PDF
$35.00

Relay Green 120v

SKU:
460
This relay turns the heat on and off in a 120v instrument.
$41.00

Relay Green 220v

SKU:
461
This relay turns the heat on and off in a 220v instrument.
$49.00

Relay Green 24v

SKU:
462
This relay is used within the control system.
$49.00

Relay SS (Heater part)

SKU:
6032
This solid state (SS) relay controls power to the heater.
$89.00

Solvent Filter Element

SKU:
146.1
This metal screen filters particles and should be cleaned regularly. XT15 Service Procedure 17 provides instructions for accessing this part.
$17.00

Splat Display Assembly

SKU:
X90
Mounted on the front of the instrument, this LCD screen displays temperature and time left during an extraction operation.
$93.00

Thermister Assembly

SKU:
RD3
This thermistor is used to measure the temperature within the drying chamber.
$56.00

Thermistor Assembly

SKU:
H32
This probe is used to measure the temperature within the Extraction Chamber of the instrument.
$113.00

Valve Seat

SKU:
Z132
This part goes inside the Solenoid Supply Valves on the XT10, XT15, HCl, A2000 & TDF instruments and is inserted onto the end of the Valve Plunger. Note: XT10 & XT15 - This part seals the water valve to prevent leaking or back flow. For details on replacing this part refer to the following Service Procedures:
  • XT10/XT15 Shared Service Procedure 5
  • HCl (Pending)
  • A2000 Service Procedure 16
  • TDF Service Procedure 17
$15.00

Valve Spring

SKU:
Z135
This spring goes inside the Solenoid Supply Valves on the XT10, XT15, HCl, A2000 & TDF instruments and is inserted inside the Valve Plunger. Note: XT10 & XT15 - This spring cannot be used in valve Q5. For replacing the Q5 Valve Spring, contact [email protected]. For details on replacing this part refer to the following Service Procedures:
  • XT10/XT15 Shared Service Procedure 5
  • HCl (Pending)
  • A2000 Service Procedure 16
  • TDF Service Procedure 17
$3.00

Viton O-ring

SKU:
Z133
This Viton O-ring is used within the Solenoid Supply Valves on the XT10, XT15, HCl, A2000 & TDF instruments for proper sealing and replaces the valve body seal O-ring around the inside of the valve guide tube. For details on replacing this part refer to the following Service Procedures:
  • XT10/XT15 Shared Service Procedure 5
  • HCl (Pending)
  • A2000 Service Procedure 16
  • TDF Service Procedure 17
$5.00

Water Filter Assembly (HCL & XT)

SKU:
X97
This filter is used in the water supply line.
$34.00