Digestion Vessel with Port & Cap

SKU:
FLEX55
For use in the ANKOMFLEX Analyte Extractor. Precision ground glass vessel with port and cap; used in the digestion step of the analysis. The port allows the addition of internal standards. A FLEX55 combined with a FLEX54 form a complete Digestion Vessel Assembly.
$301.00

Magnetic Cross Stir-Bar

SKU:
9415
For use in the ANKOMFLEX Analyte Extractor. PTFE magnetic cross stir-bar; used in each assembled digestion vessel.
$21.00

Round Bottom Flask

SKU:
9364
For use in the ANKOMFLEX Analyte Extractor. Precision ground round bottom flask with a 34-15 taper ground joint; used in the evaporation step of the instrument.
$120.00

Sorbent Disposal Bag - 20 count

SKU:
FLEX-SDB
The Sorbent Disposal Bags are used to remove any residual solvent left in the sorbent material after a run is complete. The contents of four SPE columns fit into one Sorbent Disposal Bag. For further instructions, follow service procedure FLS015.
 
Related Documents: 
Procedure Title Download
15 FLS015 Sorbent Disposal Process View PDF
$19.00

Vessel Bottom Assembly

SKU:
FLEX54
For use in the ANKOMFLEX Analyte Extractor. Virgin PTFE white vessel bottom assembly; used in the digestion step of the analysis. A FLEX54 combined with a FLEX55 form a complete Digestion Vessel Assembly.
$144.00

Check Sample- Infant Formula

SKU:
FLEX65
This sample is to be used with the ANKOM FLEX/FLEXI Analyte Extractors for vitamin A and E.  The purpose of the check sample is both to ensure proper function of the instrument and correct procedural technique.  If your results do not meet the expected range, first check your procedural steps.  If the method has been followed properly, contact ANKOM Technology at www.ankom.com/contact/analytical-services or call 1-315-986-8090.
 
Related Documents: 
Procedure Title Download
Certificate_of_Analysis_Vitamin_Check_Sample_2022 View PDF
$25.00

Flask Clip Assembly

SKU:
FLEX57
The Flask Clip Assemblies are an adhesive-backed spring clip used to secure the round bottom flasks in position again the recovery door.
$11.00

FLEX Maintenance Kit

SKU:
FLEX66
The FLEX Maintenance Kit provides the essential items needed to keep your FLEX Analyte Extractor operating smoohtly. The following items are included:
4 - Container Filters (#8202)
4 - Vessel Top O-Ring (#9231)
4 - Column top O-Ring (#9280)
1 - Pinch Valve Tube (#9313)
4 - Round Belt 1/8" x 9.5" (#9412)
4 - Vessel Bottom O-Ring, Small (#9423)
4 - Vessel Bottom O-Ring, Large (#9424)
1 - Diaphram Check Valve Assembly (#FLEX71)     
  
 
$450.00

FLEX Thermistor Assembly

SKU:
FLEX21
The FLEX21 Thermistor Assemblies are used to monitor temperature at eight locations.  One is used to monitor the vessels' temperatures and is marked 46.  One is used to monitor the reference temperature surrounding the round bottom flasks and is marked 47.  Four of these are used in the round bottom flasks and are numbered 50, 51, 52 and 53.  One is used in the oven and is marked 54.  One is used in the evaporation inlet and is marked 55.  Specify 46, 47, 50, 51, 52, 53, 54 or 55 at checkout.
$103.00

High Pressure Sensor Assembly

SKU:
FLEX10
The High Pressure Sensor Assembly is used to monitor the main nitrogen input line pressure to the instrument.
$68.00

High Temperature Thermistor Assembly

SKU:
FLEX24
The FLEX24 High Temperature Thermistor Assembly is marked 56 and is used to monitor the temperature within the oven.
$146.00

Low Pressure Sensor Assembly

SKU:
FLEX9
The Low Pressure Sensor Assembly is used to monitor nitrogen (N2) line pressure in two locations.  One marked 43 monitors N2 going to the four round bottom flasks used for solvent evaporation.  One marked 45 monitors N2 Low Pressure and is displayed on screen.  This is used to assist in pressurized draining of the four columns and purging lines.  Specify 43 or 45 at checkout.
$81.00

Motor with 4-Wire Cable Assembly

SKU:
FLEX20
The Motor with 4-wire cable is a stepper motor which operates the vessels' magnetic stirrers.
$302.00

Optical Bubble Sensor Assembly

SKU:
FLEX22
The Optical Bubble Sensor Assemblies function as a drain sensor and monitor fluid lines at five locations.  Four sensors are used to confirm drain of the vessels.  Those used for vessels 1, 2, 3 and 4 are marked 31, 32, 33,34, respectively.   One marked 35 is used to monitor fluid exiting the Process Pump.  Specify Vessel 1, 2, 3, 4 or Pump at check out.
$197.00

Process Pump Assembly

SKU:
FLEX43
The Process Pump is the fluid delivery pump used to deliver all reagents from the reservoirs to the vessels.
$1,182.00

Rubber Cleaning Strip

SKU:
FLEX61
Used only in the cleaning of the Vessel Tops at the end of the run for Fat analyses that use hydrochloric acid (HCL). Procedure for use is available in the FLEX Operator's Manual.
 
$30.00

Thermal Cut-off Assembly

SKU:
FLEX23
The Thermal Cut-off Assembly is used in the heater for the oven.  It consists of a non-resettable thermal fuse that shuts down power to the heater if the temperature exceeds 240°C. 
$34.00

Vent Valve Assembly

SKU:
FLEX32
The Vent Valve Assembly functions to release pressure from the vessels during vessel fill and saponification.
$846.00

Vessel Low Pressure Sensor Assembly

SKU:
FLEX19
The Vessel Low Pressure Sensor Assembly is used to monitor pressure in the four vessels during filling and saponification.  Specify vessel 1, 2, 3 or 4 at checkout.
$97.00

Waste Bottle Assembly

SKU:
FLEX49
The Waste Bottle Assembly is used to capture waste from the FLEX instrument and includes the waste collection bottle, cap and tubing.
$157.00