Resource Center

Used for globe vent valve. Located inside the cabinet left side panel.

Located inside Evaporation Chamber.

For use in the ANKOM FLEX Analyte Extractor. High Strength PTFE magnetic stir-bar; used in each assembled digestion vessel for more difficult to mix samples.

The Process Pump is the fluid delivery pump used to deliver all reagents from the reservoirs to the vessels.

The Motor with 4-wire cable is a stepper motor which operates the vessels' magnetic stirrers.

The FLEX24 High Temperature Thermistor Assembly is marked 56 and is used to monitor the temperature within the oven.

For use in the ANKOM FLEX Analyte Extractor. Precision ground glass vessel with port and cap; used in the digestion step of the analysis. The port allows the addition of internal standards. A FLEX55 combined with a FLEX54 form a complete Digestion...

For use in the ANKOM FLEX Analyte Extractor. PTFE magnetic cross stir-bar; used in each assembled digestion vessel.

For use in the ANKOM FLEX Analyte Extractor. Precision ground round bottom flask with a 34-15 taper ground joint; used in the evaporation step of the instrument.

Located in #FLEX30 Slide Valve and #FLEX32 Vent Valve assemblies Rev A.

The Thermal Cut-off Assembly is used in the heater for the oven. It consists of a non-resettable thermal fuse that shuts down power to the heater if the temperature exceeds 240°C.

The Vent Valve Assembly functions to release pressure from the vessels during vessel fill and saponification.

Located in Column Top Assembly.

Located in Vessel Top inside the Digestion Oven.

The Waste Bottle Assembly is used to capture waste from the FLEX instrument and includes the waste collection bottle, cap, and tubing.

The Flask Clip Assemblies are an adhesive-backed spring clip used to secure the round bottom flasks in position again the recovery door.

This relay turns the heat source on and off.

The Helical Coupler is used on the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. It couples the agitator shaft with the motor to provide sample agitation within the vessel. For the A200/A200I instruments, refer to Service Procedure...

This resettable breaker is used to protect the instrument against power surges that are out-of-specification.

The ETS Snap Disc Thermostat is used in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. It interrupts power to the heating element in an over-temperature condition.

This assembly includes a probe that provides an accurate temperature to the Athena controller.

This assembly connects the pressure switch to the digestion vessel.

This timer controls the digestion time.

The Low Pressure Sensor Assembly is used to monitor nitrogen (N2) line pressure in two locations. One marked 43 monitors N2 going to the four round bottom flasks used for solvent evaporation. One marked 45 monitors N2 Low Pressure and is displayed on...

The High Pressure Sensor Assembly is used to monitor the main nitrogen input line pressure to the instrument.

The FLEX21 Thermistor Assemblies are used to monitor temperature at eight locations. One is used to monitor the vessels' temperatures and is marked 46. One is used to monitor the reference temperature surrounding the round bottom flasks and is marked...

The FLEX Maintenance Kit provides the essential items needed to keep your FLEX Analyte Extractor operating smoohtly. The following items are included: 4 - Container Filters ( Part #: 8202 ) 4 - Vessel Top O-Ring ( Part #: 9231 ) 4 - Column top O-Ring...

Pneumatic Control Solenoid Valve used in TDF and FLEX Instruments. Replacement part for a faulty Solenoid Valve.

Used with Digestion Vessel Glass ( Part #: FLEX55 ) seal port.

Small O-ring located in Vessel Bottom Assembly ( Part #: FLEX54 ) on the bottom side.

Large O-ring located in the Vessel Bottom Assembly ( Part #: FLEX54 ) on the top, inside.

The Nitrogen Flowmeter is used to regulate nitrogen flow to FLEX instrument.

This access panel is designed with a viewing window, allowing users to easily monitor their slide valve condition.

This is a replacement upper tray for the bag suspender which is found in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. Eight of these are used in the bag suspender assembly.

These lamps light the inside of the heat and agitate switches.

The replacement Hose Coupler is used on the DELTA/DELTAI, A200/A200I, and A2000/A2000I Fiber instruments. It connects to the drain hose at the side of the instrument. Includes 2 pieces.

This bolt is used for securing the lid and hinge block assembly to the vessel.