Resource Center

This relay turns the heat source on and off.

The Helical Coupler is used on the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. It couples the agitator shaft with the motor to provide sample agitation within the vessel. For the A200/A200I instruments, refer to Service Procedure...

This resettable breaker is used to protect the instrument against power surges that are out-of-specification.

The ETS Snap Disc Thermostat is used in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. It interrupts power to the heating element in an over-temperature condition.

This assembly includes a probe that provides an accurate temperature to the Athena controller.

This assembly connects the pressure switch to the digestion vessel.

This timer controls the digestion time.

This is a replacement upper tray for the bag suspender which is found in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. Eight of these are used in the bag suspender assembly.

These lamps light the inside of the heat and agitate switches.

The replacement Hose Coupler is used on the DELTA/DELTAI, A200/A200I, and A2000/A2000I Fiber instruments. It connects to the drain hose at the side of the instrument. Includes 2 pieces.

This bolt is used for securing the lid and hinge block assembly to the vessel.

The Kynar Tip and Washer assembly is used when the Kynar tip has become worn. It is located at the bottom of the bag suspender used in the DELTA/DELTAI, A200/A200I, and A2000/A2000I Fiber instruments. A worn tip can inhibit proper agitation and...

This part protects the 120v A200 instrument against power surges that are out-of-specification.

To protect the interior of the instrument, this collection chamber catches fluid in the event of an internal leak.

This assembly shows if the packing has started to leak.

This assembly controls the heat to the digestion vessel.

This assembly heats the digestion vessel in the 220v A200I instrument.

The Outer Exhaust Hose Assembly is used in the DELTA/DELTAI and A200/A200I Fiber instruments. It drains waste solutions from the digestion vessel.

The Bag Suspender Rod w/ Nut Assembly is used when damage to the rod or pitting has occurred. It runs through the middle of the bag suspender and holds the nine trays in place and is used in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber...

The Bag Weigh Holder is used to hold a filter bag open for easy insertion of the sample. This part is especially useful during the weighing process.

The Hinge Block Assembly is found in the A200/A200I Fiber Instruments. The assembly includes a shoulder bolt and is used to secured the lid to the vessel during sample digestion.

This hose carries waste from the vessel to the outer exhaust hose. Includes hose with clips.

This assembly heats the digestion vessel in the 120v instrument.

The Bag Weight Machined is used on the top of the bag suspender within the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. It is necessary to hold the trays in place, which, in turn, hold the filter bags in suspension, during the digestion...

The Brass Packing Nut is used in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber Instruments. When properly tightened, this ensures that the packing materials create a seal and prevent leaks from the vessel into the interior cabinet. For the A200...

This switch turns power on and off to the instrument.

The Drip Tray is part of the Maintenance Alert Assembly and is used in the DELTA, A200, and A2000 instruments. It functions as a collector for a fluid leak around the agitator, diverting it away from the motor.

This is a replacement bottom tray for the bag suspender, which is found in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments.

The Agitator Apron is used in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. It serves to funnel fluid away from the motor and into the maintenance alert assembly.

The Bag Suspender w/ Weight is used within the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. It is the entire array that holds the filter bags in the vessel and ensures proper circulation of solutions and uniform digestion of the samples.

This switch turns the heat to the digestion vessel on and off.

The Packing Set is used in the DELTA/DELTAI, A200/A200I, and A2000/A2000I Fiber instruments. Its purpose is to create a seal and keep the solution from leaking from the vessel into the interior cabinet. This includes two lengths of graphite rope...

This assembly includes the handle and clamping device used for sealing the lid and hinge block assembly to the vessel.

This motor agitates the bag suspender at the proper RPM in the 120v instrument.

The Open End Wrench 1-1/8" is used to tighten the Brass Packing Nut ( Part #: 640 ) found on the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments.

This switch turns the agitation to the digestion vessel on and off.

The Agitator with Packing Set is used in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. This is used to replace a worn or pitted agitator and with the packing set creates a seal to keep solution from leaking from the vessel into the...

The Lid & Hinge Block Assembly is found in the A200/A200I Fiber Instruments. Together, these seal the vessel during sample digestion. The assembly includes both the lid and the hinge block that secures the lid closed, as well as two replacement...

This assembly includes the O-ring used to seal the digestion vessel and the glue to secure the O-ring.