Resource Center

The On/Off/Heat/Rotate Power Switch is used on the following ANKOM instruments: XT10/XT10I, XT15/XT15I, HCl/HClI, RD/RDI, TDF/TDFI, D200/D200I, DELTA/DELTAI, A200/A200I, A2000/A2000I, FLEX/FLEXI. On the D200/D200I Daisy Incubator, this switch also...

The Moisture Stop Weigh Pouch contains a desiccant packet which absorbs moisture within the zipper bag. It is used when cooling and weighing filter bags to avoid unwanted absorption of moisture in the dried samples which would skew results.

This relay turns the heat source on and off.

This drive belt connects the motor and the drive roller ( Part #: 834 ).

This part protects the D200/D200I instruments against power surges that are out-of-specification.

The jars rotate on this roller.

This motor turns the jars during digestion.

Replacement fused filter plug and on/off switch.

These bulbs are used for heating the 120-130v DAISY instrument.

The Bag Weigh Holder is used to hold a filter bag open for easy insertion of the sample. This part is especially useful during the weighing process.

Belt 808 rides on this roller.

This drive roller connects the motor to the drive pulleys.

This is a 100 hr timer assembly for monitoring incubation times of samples in the ANKOM Daisy II Incubator (D200/D200I).

Filter bags are placed in this jar during digestion.

This dual voltage fan drives air through the Daisy Incubator (D200/D200I) to maintain consistent heat.

This probe provides an accurate temperature to the Athena controller.

This motor turns the jars during digestion.

Belt 808 rides on this roller.

The jars rest on these bumpers during digestion.

Replacement programmed controller for the D200/D200I Daisy II Incubator. For installation instructions, refer to DAISY Service Procedure Controller Installation (DS002).

This lid seals the jar during digestion.

This vent valve is used in the jar lid ( Part #: D2.5 ) for releasing pressure from the jars during digestion.

These bulbs are used for heating the 220-240v DAISY instrument.

During digestion, the jars ride on this belt to prevent them from slipping.

The fluid supply distribution manifold directs input fluids to the six IDF/SDF stations. To replace the supply manifold in your instrument, follow TDF Service Procedure Supply Manifold Replacement (TS029).

The Mixing Pad Assembly may require replacement if bent or if the pad has become loose. Refer to TDF Service Procedure Mixing Pad Adjustment (TS010) to ensure proper alignment.

This is an enzyme container used for supplying Amylase to the instrument.

The largest contributor to poor TDF results is the effect of static electricity on the weighing process. The TDF52 Bag Weigh Holder is used during the weighing process to eliminate static electricity while the bag is being weighed.

This container is used with the AOAC 2009.01/2011.25 methods.

The Vacuum Sensor Assembly monitors pressures on the supply lines and is used to identify empty containers, plugged fluid lines, or damage to a supply line. For replacement instructions, refer to Service Procedure Vacuum Sensor Installation (TS013).

Replacement tube set for all seven pinch valves [Enzymes, IDF inlet(2), SDF Inlet(2) and Waste(2)]. Refer to Service Procedure Tube Replacement (Pinch Valves) (TS005) for installation instructions.

This clamp bar is used in the IDF part of the instrument to close the top of the Filter Bag.

This clamp bar is used in the SDF part of the instrument to close the top of the Filter Bag.

The Paddle Bar Replacement Kits includes the Paddle Bar Assembly and the tools required for its installation. The Paddle Bar functions as both a paddle mixer and heater with embedded sensors to allow for independent heat regulation at each position...

This tool is used to view the spray tips for obstructions during cleaning and maintenance.