Resource Center

Used for globe vent valve. Located inside the cabinet left side panel.

Located inside Evaporation Chamber.

For use in the ANKOM FLEX Analyte Extractor. High Strength PTFE magnetic stir-bar; used in each assembled digestion vessel for more difficult to mix samples.

The Process Pump is the fluid delivery pump used to deliver all reagents from the reservoirs to the vessels.

The Motor with 4-wire cable is a stepper motor which operates the vessels' magnetic stirrers.

The FLEX24 High Temperature Thermistor Assembly is marked 56 and is used to monitor the temperature within the oven.

For use in the ANKOM FLEX Analyte Extractor. Precision ground glass vessel with port and cap; used in the digestion step of the analysis. The port allows the addition of internal standards. A FLEX55 combined with a FLEX54 form a complete Digestion...

For use in the ANKOM FLEX Analyte Extractor. PTFE magnetic cross stir-bar; used in each assembled digestion vessel.

For use in the ANKOM FLEX Analyte Extractor. Precision ground round bottom flask with a 34-15 taper ground joint; used in the evaporation step of the instrument.

Located in #FLEX30 Slide Valve and #FLEX32 Vent Valve assemblies Rev A.

The Thermal Cut-off Assembly is used in the heater for the oven. It consists of a non-resettable thermal fuse that shuts down power to the heater if the temperature exceeds 240°C.

The Vent Valve Assembly functions to release pressure from the vessels during vessel fill and saponification.

Located in Column Top Assembly.

Located in Vessel Top inside the Digestion Oven.

The Waste Bottle Assembly is used to capture waste from the FLEX instrument and includes the waste collection bottle, cap, and tubing.

The Flask Clip Assemblies are an adhesive-backed spring clip used to secure the round bottom flasks in position again the recovery door.

This module cap includes a notch that allows for a battery extension cable.

The RF Gen 3 Circuit Board contains the electronics used for communication with all RF1X / RF5X modules.

The RF Solenoid assembly is used to replace a faulty solenoid pinch valve within the RF1 or RF1X Module.

The RF28 Air Purge Assembly can be used to purge the glass bottle prior to an experiment, or to pressurize the module assembly (through the Luer Duckbill Check Valve, Part #: 7139 ) to check for leaks. For module purge instructions, see RF Service...

This cable is used to connect the Dual Lead Battery Pack ( Part #: RF46 ) to the 10-Station Battery Charger ( Part #: RF25 ). Longer extension cables are available upon request.

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7056 bottle provides the following features: - up to 250ml of space to hold analysis material - a protective coating...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7129 bottle provides the following features: - up to 1000ml of space to hold analysis material - an Amber tint to...

The RF Gas Production System uses rechargeable battery packs ( #RF16 / #RF46 ). The RF25 10-Station Battery Charger is used to charge the RF16/RF46 Rechargeable Battery Packs. As the name says, this charger can charge 10 batteries at one time.

This one-way valve is used for adding gas into the glass bottle of an RF1 module. This is often done to purge the bottle of existing gases. To push gas into the bottle using an Air Purge Assembly ( Part #: RF28 ), see RF Service Procedure Purge...

The RF2 Base Coordinator uses an antenna to communicate with the RF1 modules. The 7143 antenna is a replacement part for the one connected to the RF2 Base Coordinator, and/or the one connected to the RF29 Antenna Extension Assembly.

The Low Pressure Sensor Assembly is used to monitor nitrogen (N2) line pressure in two locations. One marked 43 monitors N2 going to the four round bottom flasks used for solvent evaporation. One marked 45 monitors N2 Low Pressure and is displayed on...

The High Pressure Sensor Assembly is used to monitor the main nitrogen input line pressure to the instrument.

The FLEX21 Thermistor Assemblies are used to monitor temperature at eight locations. One is used to monitor the vessels' temperatures and is marked 46. One is used to monitor the reference temperature surrounding the round bottom flasks and is marked...

The FLEX Maintenance Kit provides the essential items needed to keep your FLEX Analyte Extractor operating smoohtly. The following items are included: 4 - Container Filters ( Part #: 8202 ) 4 - Vessel Top O-Ring ( Part #: 9231 ) 4 - Column top O-Ring...

Pneumatic Control Solenoid Valve used in TDF and FLEX Instruments. Replacement part for a faulty Solenoid Valve.

Used with Digestion Vessel Glass ( Part #: FLEX55 ) seal port.

Small O-ring located in Vessel Bottom Assembly ( Part #: FLEX54 ) on the bottom side.

Large O-ring located in the Vessel Bottom Assembly ( Part #: FLEX54 ) on the top, inside.

The Nitrogen Flowmeter is used to regulate nitrogen flow to FLEX instrument.

This access panel is designed with a viewing window, allowing users to easily monitor their slide valve condition.

The RF22.5 Vent Valve Adapter is used to attach the 7043 Syringe to the vent valve tube to aid in cleaning the vent valve on a Gas Production Module (Part #: RF1). For cleaning instructions, see RF Service Procedure Vent Valve Cleaning (RFS006).

This 1.8L Wide Mouth Bottle assembly attaches directly to an RF1 electrical assembly just like all of the smaller bottles. This RF1 configuration provides the largest bottle by volume and by opening available with the RF Gas Production System. If you...

This battery kit includes the following: - 1-Dual Lead RF Rechargeable Battery Pack ( Part #: RF46 ) - 1-5 ft Battery Extension Cable ( Part #: RF44 ) - 1-Red Cap with a notch for the extension cable Longer-length cables are available upon request.

This 1.8L Wide Mouth Bottle is used in the RF42 assembly and is the largest bottle by volume and by opening available with the RF Gas Production System. If you have a large sample to analyze such as dough, this bottle might work best for your needs...