Resource Center

The On/Off/Heat/Rotate Power Switch is used on the following ANKOM instruments: XT10/XT10I, XT15/XT15I, HCl/HClI, RD/RDI, TDF/TDFI, D200/D200I, DELTA/DELTAI, A200/A200I, A2000/A2000I, FLEX/FLEXI. On the D200/D200I Daisy Incubator, this switch also...

This is the fan assembly in the 120v RD Dryer.

This is the controller with display used in the 220v RD Dryer.

The H37 Bag Holder is used to hold the bags in the HCl/HClI Extraction Chamber during as assay. This assembly holds 15 bags. Can also be used in the RD/RDI Dryers.

Attaches on the top of the RD/RDI Dryer. This filter is used when drying filter bags before and after a fat extraction done with an ANKOM XT10/XT10I or an ANKOM XT15/XT15I Extractor.

This is the controller with display used in the 120v RD Dryer.

The H33 Bag Holder is used to hold the bags in the HCl Extraction Chamber during as assay. This assembly holds 20 bags. Can also be used in the RD/RDI Dryers.

Attaches on the top of the RD/RDI Dryer. This filter is used when drying filter bags after a hydrolysis operation is done with an ANKOM HCl/HCI Hydrolysis System.

This is the heater assembly in the 220v RD Dryer.

This is the fan assembly in the 220v RD Dryer.

This 10 amp fuse is used on the DELTAI and A2000I Fiber instruments (220v) along with RD (120v) and RDI (220v). It helps protect the instrument from a possible power surge.

This thermistor is used to measure the temperature within the RD/RDI Dryers drying chamber.

The Stainless Steel Latch secures the RD1 or RD2 Filter to the ANKOM Rapid Dryer (RD/RDI). One is used on either side of the Rapid Dryer.

This is the heater assembly in the 120v RD Dryer.

This relay turns the heat source on and off.

This drive belt connects the motor and the drive roller ( Part #: 834 ).

This part protects the D200/D200I instruments against power surges that are out-of-specification.

The jars rotate on this roller.

This motor turns the jars during digestion.

Replacement fused filter plug and on/off switch.

This drive roller connects the motor to the drive pulleys.

This is a 100 hr timer assembly for monitoring incubation times of samples in the ANKOM Daisy II Incubator (D200/D200I).

Filter bags are placed in this jar during digestion.

This dual voltage fan drives air through the Daisy Incubator (D200/D200I) to maintain consistent heat.

These bulbs are used for heating the 120-130v DAISY instrument.

The Bag Weigh Holder is used to hold a filter bag open for easy insertion of the sample. This part is especially useful during the weighing process.

Belt 808 rides on this roller.

This probe provides an accurate temperature to the Athena controller.

This motor turns the jars during digestion.

Belt 808 rides on this roller.

The jars rest on these bumpers during digestion.

Replacement programmed controller for the D200/D200I Daisy II Incubator. For installation instructions, refer to DAISY Service Procedure Controller Installation (DS002).

This lid seals the jar during digestion.

This vent valve is used in the jar lid ( Part #: D2.5 ) for releasing pressure from the jars during digestion.

The Moisture Stop Weigh Pouch contains a desiccant packet which absorbs moisture within the zipper bag. It is used when cooling and weighing filter bags to avoid unwanted absorption of moisture in the dried samples which would skew results.

These bulbs are used for heating the 220-240v DAISY instrument.

During digestion, the jars ride on this belt to prevent them from slipping.