Resource Center

The A42 Pressure Sensor Assembly is used to replace a faulty pressure sensor on the A2000/A2000I vessel, where it monitors dynamic pressure throughout the run.

This probe provides an accurate temperature to the Athena controller.

Replacement programmed controller for the D200/D200I Daisy II Incubator. For installation instructions, refer to DAISY Service Procedure Controller Installation (DS002).

Filter bags are placed in this jar during digestion.

This lid seals the jar during digestion.

This motor turns the jars during digestion.

This motor turns the jars during digestion.

This assembly includes a probe that provides an accurate temperature to the Athena controller.

Replacement fused filter plug and on/off switch.

This assembly heats the digestion vessel in the A200I, 220v instrument.

The Kynar Tip and Washer assembly is used when the Kynar tip has become worn. It is located at the bottom of the bag suspender used in the DELTA/DELTAI, A200/A200I, and A2000/A2000I Fiber instruments. A worn tip can inhibit proper agitation and...

The Outer Exhaust Hose Assembly is used in the DELTA/DELTAI and A200/A200I Fiber instruments. It drains waste solutions from the digestion vessel.

The Bag Suspender Rod w/ Nut Assembly is used when damage to the rod or pitting has occurred. It runs through the middle of the bag suspender and holds the nine trays in place and is used in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber...

This assembly connects the pressure switch to the digestion vessel in the A200 instrument.

This part protects the 120v A200 instrument against power surges that are out-of-specification.

This timer controls the digestion time.

This switch turns the heat to the digestion vessel on and off.

This switch turns the agitation to the digestion vessel on and off.

The Bag Weigh Holder is used to hold a filter bag open for easy insertion of the sample. This part is especially useful during the weighing process.

The Packing Set is used in the DELTA/DELTAI, A200/A200I, and A2000/A2000I Fiber instruments. Its purpose is to create a seal and keep the solution from leaking from the vessel into the interior cabinet. This includes two lengths of graphite rope...

To protect the interior of the instrument, this collection chamber catches fluid in the event of an internal leak.

This assembly shows if the packing has started to leak.

The Agitator with Packing Set is used in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. This is used to replace a worn or pitted agitator and with the packing set creates a seal to keep solution from leaking from the vessel into the...

This assembly controls the heat to the digestion vessel.

The Hinge Block Assembly is found in the A200/A200I Fiber Instruments. The assembly includes a shoulder bolt and is used to secured the lid to the vessel during sample digestion.

This hose carries waste from the vessel to the outer exhaust hose. Includes hose with clips.

The Lid & Hinge Block Assembly is found in the A200/A200I Fiber Instruments. Together, these seal the vessel during sample digestion. The assembly includes both the lid and the hinge block that secures the lid closed, as well as two replacement...

This assembly includes the O-ring used to seal the digestion vessel and the glue to secure the O-ring.

Used in both the XT10/XT10I and XT15/XT15I. This metal screen filters particles and should be cleaned regularly. XT15 Service Procedure Instrument and Components Cleaning (X5S017) provides instructions for accessing this part.

This assembly includes the handle and clamping device used for sealing the lid and hinge block assembly to the vessel.

This motor agitates the bag suspender at the proper RPM in the A200, 120v instrument.

This motor agitates the bag suspender at the proper RPM in the A200I, 220v instrument.

This assembly heats the digestion vessel in the A200, 120v instrument.

The Process Pump is the fluid delivery pump used to deliver all reagents from the reservoirs to the vessels.

The Waste Bottle Assembly is used to capture waste from the FLEX instrument and includes the waste collection bottle, cap, and tubing.

The Flask Clip Assemblies are an adhesive-backed spring clip used to secure the round bottom flasks in position again the recovery door.

This connects power to the Paddle Bar.

The jars rotate on this roller.

Used in both the XT10/XT10I and XT15/XT15I. This valve spring is for the Q5 solvent valve only. This spring should not be used in any other valve.

This module cap includes a notch that allows for a battery extension cable.

This container is used to hold the Buffer for TDF CODEX methods.

This 90° Brass Elbow is found in the DELTA/DELTAI and A2000/A2000I Fiber instruments and connects the drain valve to the exhaust hose.