Resource Center

The RF Gas Production System uses rechargeable battery packs ( #RF16 / #RF46 ). The RF25 10-Station Battery Charger is used to charge the RF16/RF46 Rechargeable Battery Packs. As the name says, this charger can charge 10 batteries at one time.

This one-way valve is used for adding gas into the glass bottle of an RF1 module. This is often done to purge the bottle of existing gases. To push gas into the bottle using an Air Purge Assembly ( Part #: RF28 ), see RF Service Procedure Purge...

The RF2 Base Coordinator uses an antenna to communicate with the RF1 modules. The 7143 antenna is a replacement part for the one connected to the RF2 Base Coordinator, and/or the one connected to the RF29 Antenna Extension Assembly.

The RF28 Air Purge Assembly can be used to purge the glass bottle prior to an experiment, or to pressurize the module assembly (through the Luer Duckbill Check Valve, Part #: 7139 ) to check for leaks. For module purge instructions, see RF Service...

This cable is used to connect the Dual Lead Battery Pack ( Part #: RF46 ) to the 10-Station Battery Charger ( Part #: RF25 ). Longer extension cables are available upon request.

This module cap includes a notch that allows for a battery extension cable.

The RF Gen 3 Circuit Board contains the electronics used for communication with all RF1X / RF5X modules.

The RF Solenoid assembly is used to replace a faulty solenoid pinch valve within the RF1 or RF1X Module.

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7056 bottle provides the following features: - up to 250ml of space to hold analysis material - a protective coating...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7129 bottle provides the following features: - up to 1000ml of space to hold analysis material - an Amber tint to...

The RF22.5 Vent Valve Adapter is used to attach the 7043 Syringe to the vent valve tube to aid in cleaning the vent valve on a Gas Production Module (Part #: RF1). For cleaning instructions, see RF Service Procedure Vent Valve Cleaning (RFS006).

This 1.8L Wide Mouth Bottle assembly attaches directly to an RF1 electrical assembly just like all of the smaller bottles. This RF1 configuration provides the largest bottle by volume and by opening available with the RF Gas Production System. If you...

This battery kit includes the following: - 1-Dual Lead RF Rechargeable Battery Pack ( Part #: RF46 ) - 1-5 ft Battery Extension Cable ( Part #: RF44 ) - 1-Red Cap with a notch for the extension cable Longer-length cables are available upon request.

This 1.8L Wide Mouth Bottle is used in the RF42 assembly and is the largest bottle by volume and by opening available with the RF Gas Production System. If you have a large sample to analyze such as dough, this bottle might work best for your needs...

This wrist strap minimizes the static electricity discharge that can negatively affect the programming on the electronics chip within your RF1 module. You should use this strap whenever you are servicing RF1 electronics, including whenever you...

The RF16 Rechargeable Battery Packs are used to provide power to the RF1 & RF5 Gas Production Module electronics. Use an RF25 10 Station Charger to recharge your batteries.

The RF22 Vent Valve Cleaning Kit is used to clean the vent valve on a Gas Production Module (RF1). For cleaning instructions, see RF Service Procedure Vent Valve Cleaning (RFS006).

Radio frequency communication can be impacted by distance and obstructions such as metal structures. The RF29 10 ft Antennae Extension Assembly can be connected to the RF2 Base Coordinator to improve radio frequency communication by allowing the...

The pressure inside the glass bottle of the RF1 Gas Production Module is measured using a pressure sensor. The data from the sensor is then communicated through the RF2 coordinator to the GPS software using wireless technology. The RF31 Pressure...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7120 bottle provides the following features: - up to 100ml of space to hold analysis material - a protective coating...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7128 bottle provides the following features: - up to 500ml of space to hold analysis material - an Amber tint to...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7131 bottle provides the following features: - up to 500ml of space to hold analysis material - a protective coating...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7154 bottle provides the following features: - up to 250ml of space to hold analysis material - an Amber tint to...

This adapter lid with GL45 threads allows RF Modules to fit 1.8L wide mouth jar ( Part #: 7181 ).

The Chemical Receptacle is used to house an NaOH (or stronger Base) when performing oxygen consumption studies. The function of the Base material is to scavenge the CO2 produced by the aerobic metabolism. This produces a negative pressure as the O2...

The RF Gas Production System bottles that include a septa port use a 3 mm 2-sided PTFE coated Silicone Septa to provide an easy to penetrate seal while providing minimal pressure loss per penetration. The RF35 pack includes 10 septa.

The RF41 Synthetic Grease w/PTFE is a non-toxic lubricant used to assist in creating a seal between the RF34 Viton® Gasket and the module/bottle, and between the PTFE coated septa and the septa port on the bottle. For application instructions...

Along with a 3 ft Extension Cable ( Part #: RF44 ), the Dual Lead Rechargeable Battery Pack ( Part #: RF46 ) provides the capability to charge your RF1 module's battery during an experiment by keeping it connected to the Battery Charger ( Part #...

The RF45 and RF45X Programmed RF Chips w/antenna facilitate communication between the Gas Production Modules, the Module Zero, and the Gas Production Base Coordinator.

The RF2X Base Coordinator facilitates communication between the Gas Production Modules ( RF1X / RF5X ) and the GPM Software installed on a PC. One RF2X Base Coordinator services an RFS base kit of up to 50 modules. To purchase, please contact ANKOM...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7057 bottle provides the following features: - up to 1000ml of space to hold analysis material - a protective coating...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7126 bottle provides the following features: - up to 100ml of space to hold analysis material - an Amber tint to...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7127 bottle provides the following features: - up to 250ml of space to hold analysis material - an Amber tint to...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7130 bottle provides the following features: - up to 250ml of space to hold analysis material - a protective coating...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7132 bottle provides the following features: - up to 1000ml of space to hold analysis material - a protective coating...

The 7147 Male Luer Cap is used to close off the end of the Female Luer Port ( Part #: 7146 ) or the Luer Duckbill Check Valve ( Part #: 7139 ).

The Tubing Seal, 3x8 mm is used within the RF1X module to secure and seal the Pressure Sensor ( Part #: RF31 ) and Viton-Silicone Tube ( Part #: RF11 ) into their respective ports in the bottom of the module housing.

This assembly includes the silicone exhaust tube for the RF system.

Stainless Steel Tray with Spring Clamps for holding flasks from 100 to 1000ml (includes spring clamps). Works with Shaker baths WB20ISH and WB20SH .

These balls are used on top of the water bath to help maintain temperature. The balls are hollow in order to minimize condensation that can negatively impact the electronics in the RF1 modules.

The 7146 Female Luer Port is included as part of each RF1 module and used to connect the Luer Duckbill Check Valve ( Part #: 7139 ) to the RF1 module. This part can also accept the Male Luer Cap ( Part #: 7147 ) to close off the port.

The Gas Production Module Zero is used to monitor and record atmospheric pressure. This module communicates with the GPS software through the base coordinator. For generation two systems (RFS#<999), Part #: RF5 is needed, for generation three systems...

The durable Viton™ Gasket increases the seal quality between the RF1 Gas Production Module and the glass bottle. We recommend replacing gaskets when they become worn, torn, or begin to leak. The RF34 pack includes 10 Viton™ Gaskets. For installation...

A 5605 Clear Glass Bottle with protective coating is one of the bottle options that can be used with an RF1 Gas Production Module or used to collect solvent vented from the XT15 and XT10 Instruments. This bottle provides the following features: - up...

The RF Gen 2 Circuit Board contains the electronics used for communication with all RF1 / RF5 modules. For installation instructions, see RF Service Procedure Chip and Board Replacement (RFS013).

The Module Cap is the red plastic part on the top of the RF1 Gas Production Module. The cap covers the electronics in the RF1 and the electronics in the RF5 Reference Module Zero.