Resource Center

The On/Off/Heat/Rotate Power Switch is used on the following ANKOM instruments: XT10/XT10I, XT15/XT15I, HCl/HClI, RD/RDI, TDF/TDFI, D200/D200I, DELTA/DELTAI, A200/A200I, A2000/A2000I, FLEX/FLEXI. On the D200/D200I Daisy Incubator, this switch also...

The Moisture Stop Weigh Pouch contains a desiccant packet which absorbs moisture within the zipper bag. It is used when cooling and weighing filter bags to avoid unwanted absorption of moisture in the dried samples which would skew results.

This relay turns the heat source on and off.

This drive belt connects the motor and the drive roller ( Part #: 834 ).

This part protects the D200/D200I instruments against power surges that are out-of-specification.

The jars rotate on this roller.

This motor turns the jars during digestion.

Replacement fused filter plug and on/off switch.

This drive roller connects the motor to the drive pulleys.

This is a 100 hr timer assembly for monitoring incubation times of samples in the ANKOM Daisy II Incubator (D200/D200I).

Filter bags are placed in this jar during digestion.

This dual voltage fan drives air through the Daisy Incubator (D200/D200I) to maintain consistent heat.

These bulbs are used for heating the 120-130v DAISY instrument.

The Bag Weigh Holder is used to hold a filter bag open for easy insertion of the sample. This part is especially useful during the weighing process.

Belt 808 rides on this roller.

This probe provides an accurate temperature to the Athena controller.

This motor turns the jars during digestion.

Belt 808 rides on this roller.

The jars rest on these bumpers during digestion.

Replacement programmed controller for the D200/D200I Daisy II Incubator. For installation instructions, refer to DAISY Service Procedure Controller Installation (DS002).

This lid seals the jar during digestion.

This vent valve is used in the jar lid ( Part #: D2.5 ) for releasing pressure from the jars during digestion.

These bulbs are used for heating the 220-240v DAISY instrument.

During digestion, the jars ride on this belt to prevent them from slipping.

Replacement quick-release connector insert used on the ends of the supply tubes, which connect into the top of the alcohol, buffer, and water containers. Please specify the color: Blue , Red , Green , or White .

This is a maintenance tool used to clean the (6) 0.020" (0.5mm) holes in the spray tip.

Useful in the AOAC 2009.01/2011.25 methods, this cup is used to capture the filtrate that comes through the SDF Filter Bag.

The TDF120 In-Line heater Core is used to replace leaking brass tubing on the In-Line Heater. It includes connected silicone tubing for ease of installation. The heater cartridge and thermistor (temp sensor) are not included in this assembly.

The TDF129 kit provides all the tubing and parts necessary to perform the annual maintenance for a TDF instrument. This includes all the supply tubing, delivery tubing, enzyme tubing, and all related tubing plus several parts that can fatigue over...

The nitrogen check valve prevents fluid back-up from the 12 IDF/SDF delivery lines into the pneumatic lines.

This is a chemical container used for supplying 95% EtOH to the instrument.

This part provides for the proper flow of fluids as they enter the filter bags.

Before the final weighing step in a Dietary Fiber analysis, the bags must be dried. The TDF50 stainless steel Bag Drying Rack has twelve positions for holding a full set of IDF/SDF bags when drying them in an oven.

This container is used with the AOAC 2009.01/2011.25 methods.

This clamp bar is used in the SDF part of the instrument to close the Filter Bag just above the filter.

The fluid supply distribution manifold directs input fluids to the six IDF/SDF stations. To replace the supply manifold in your instrument, follow TDF Service Procedure Supply Manifold Replacement (TS029).

The Mixing Pad Assembly may require replacement if bent or if the pad has become loose. Refer to TDF Service Procedure Mixing Pad Adjustment (TS010) to ensure proper alignment.

This is an enzyme container used for supplying Amylase to the instrument.

The largest contributor to poor TDF results is the effect of static electricity on the weighing process. The TDF52 Bag Weigh Holder is used during the weighing process to eliminate static electricity while the bag is being weighed.