Part #
The On/Off/Heat/Rotate Power Switch is used on the following ANKOM instruments: XT10/XT10I, XT15/XT15I, HCl/HClI, RD/RDI, TDF/TDFI, D200/D200I, DELTA/DELTAI, A200/A200I, A2000/A2000I, FLEX/FLEXI. On the D200/D200I Daisy Incubator, this switch also...
Part #
This is the controller with display used in the 220v RD Dryer.
Part #
The H37 Bag Holder is used to hold the bags in the HCl/HClI Extraction Chamber during as assay. This assembly holds 15 bags. Can also be used in the RD/RDI Dryers.
Part #
Attaches on the top of the RD/RDI Dryer. This filter is used when drying filter bags before and after a fat extraction done with an ANKOM XT10/XT10I or an ANKOM XT15/XT15I Extractor.
Part #
This is the controller with display used in the 120v RD Dryer.
Part #
The H33 Bag Holder is used to hold the bags in the HCl Extraction Chamber during as assay. This assembly holds 20 bags. Can also be used in the RD/RDI Dryers.
Part #
Attaches on the top of the RD/RDI Dryer. This filter is used when drying filter bags after a hydrolysis operation is done with an ANKOM HCl/HCI Hydrolysis System.
Part #
This 10 amp fuse is used on the DELTAI and A2000I Fiber instruments (220v) along with RD (120v) and RDI (220v). It helps protect the instrument from a possible power surge.
Part #
This thermistor is used to measure the temperature within the RD/RDI Dryers drying chamber.
Part #
The Stainless Steel Latch secures the RD1 or RD2 Filter to the ANKOM Rapid Dryer (RD/RDI). One is used on either side of the Rapid Dryer.
Part #
RF1X Gas Production Modules can be added to an ANKOM RF Gas Production System (Base Kit). A total of 50 modules can be connected to a GEN 3 RFS system. Please specify a bottle type. NOTE: Standard RF1X modules come with 250ml bottles. For different...
Part #
This module cap includes a notch that allows for a battery extension cable.
Part #
The RF Gen 3 Circuit Board contains the electronics used for communication with all RF1X / RF5X modules.
Part #
The RF Solenoid assembly is used to replace a faulty solenoid pinch valve within the RF1 or RF1X Module.
Part #
The RF28 Air Purge Assembly can be used to purge the glass bottle prior to an experiment, or to pressurize the module assembly (through the Luer Duckbill Check Valve, Part #: 7139 ) to check for leaks. For module purge instructions, see RF Service...
Part #
This cable is used to connect the Dual Lead Battery Pack ( Part #: RF46 ) to the 10-Station Battery Charger ( Part #: RF25 ). Longer extension cables are available upon request.
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7056 bottle provides the following features: - up to 250ml of space to hold analysis material - a protective coating...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7129 bottle provides the following features: - up to 1000ml of space to hold analysis material - an Amber tint to...
Part #
The ANKOM RF Maintenance Kit provides the essential tools needed to keep your RF Gas Production System operating smoothly. The following items and instructions for each are included: - (1) RF70: Positive Control Capsule Set (set includes 5 BLUE...
Part #
The RF Gas Production System uses rechargeable battery packs ( #RF16 / #RF46 ). The RF25 10-Station Battery Charger is used to charge the RF16/RF46 Rechargeable Battery Packs. As the name says, this charger can charge 10 batteries at one time.
Part #
This one-way valve is used for adding gas into the glass bottle of an RF1 module. This is often done to purge the bottle of existing gases. To push gas into the bottle using an Air Purge Assembly ( Part #: RF28 ), see RF Service Procedure Purge...
Part #
The RF22.5 Vent Valve Adapter is used to attach the 7043 Syringe to the vent valve tube to aid in cleaning the vent valve on a Gas Production Module (Part #: RF1). For cleaning instructions, see RF Service Procedure Vent Valve Cleaning (RFS006).
Part #
This 1.8L Wide Mouth Bottle assembly attaches directly to an RF1 electrical assembly just like all of the smaller bottles. This RF1 configuration provides the largest bottle by volume and by opening available with the RF Gas Production System. If you...
Part #
This battery kit includes the following: - 1-Dual Lead RF Rechargeable Battery Pack ( Part #: RF46 ) - 1-5 ft Battery Extension Cable ( Part #: RF44 ) - 1-Red Cap with a notch for the extension cable Longer-length cables are available upon request.
Part #
This 1.8L Wide Mouth Bottle is used in the RF42 assembly and is the largest bottle by volume and by opening available with the RF Gas Production System. If you have a large sample to analyze such as dough, this bottle might work best for your needs...
Part #
This wrist strap minimizes the static electricity discharge that can negatively affect the programming on the electronics chip within your RF1 module. You should use this strap whenever you are servicing RF1 electronics, including whenever you...
Part #
The RF16 Rechargeable Battery Packs are used to provide power to the RF1 & RF5 Gas Production Module electronics. Use an RF25 10 Station Charger to recharge your batteries.
Part #
The RF22 Vent Valve Cleaning Kit is used to clean the vent valve on a Gas Production Module (RF1). For cleaning instructions, see RF Service Procedure Vent Valve Cleaning (RFS006).
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7120 bottle provides the following features: - up to 100ml of space to hold analysis material - a protective coating...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7128 bottle provides the following features: - up to 500ml of space to hold analysis material - an Amber tint to...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7131 bottle provides the following features: - up to 500ml of space to hold analysis material - a protective coating...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7154 bottle provides the following features: - up to 250ml of space to hold analysis material - an Amber tint to...
Part #
This adapter lid with GL45 threads allows RF Modules to fit 1.8L wide mouth jar ( Part #: 7181 ).
Part #
Radio frequency communication can be impacted by distance and obstructions such as metal structures. The RF29 10 ft Antennae Extension Assembly can be connected to the RF2 Base Coordinator to improve radio frequency communication by allowing the...
Part #
The pressure inside the glass bottle of the RF1 Gas Production Module is measured using a pressure sensor. The data from the sensor is then communicated through the RF2 coordinator to the GPS software using wireless technology. The RF31 Pressure...
Part #
The Chemical Receptacle is used to house an NaOH (or stronger Base) when performing oxygen consumption studies. The function of the Base material is to scavenge the CO2 produced by the aerobic metabolism. This produces a negative pressure as the O2...
Part #
Two versions of software are available depending on the RFS#: RF3: RF GPM Software 11.4 RF3X: RF GPM Software 15.0 This update to the GPM software is a major enhancement that includes many new features including: Enables up to 10 systems in one...
Part #
The RF Gas Production System bottles that include a septa port use a 3 mm 2-sided PTFE coated Silicone Septa to provide an easy to penetrate seal while providing minimal pressure loss per penetration. The RF35 pack includes 10 septa.
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7057 bottle provides the following features: - up to 1000ml of space to hold analysis material - a protective coating...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7126 bottle provides the following features: - up to 100ml of space to hold analysis material - an Amber tint to...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7127 bottle provides the following features: - up to 250ml of space to hold analysis material - an Amber tint to...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7130 bottle provides the following features: - up to 250ml of space to hold analysis material - a protective coating...
Part #
ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7132 bottle provides the following features: - up to 1000ml of space to hold analysis material - a protective coating...
Part #
The 7147 Male Luer Cap is used to close off the end of the Female Luer Port ( Part #: 7146 ) or the Luer Duckbill Check Valve ( Part #: 7139 ).
Part #
The Tubing Seal, 3x8 mm is used within the RF1X module to secure and seal the Pressure Sensor ( Part #: RF31 ) and Viton-Silicone Tube ( Part #: RF11 ) into their respective ports in the bottom of the module housing.