Resource Center

This kit is no longer available. However, the components of the X87 kit can be ordered individually as parts 969.5 and 5806. This O-Ring Kit includes an Extraction Vessel seal ( Part #: 969.5 ) and a Cup Insert Top seal ( Part #: 5806 ). Use this kit...

This is the internal computer that controls the XT10 Fat Extractor.

This is the internal computer that controls the XT15/XT15I Fat Extractor.

The LCD Screen Assembly is used in the XT10 and XT15 Fat Extractors, the HCl Hydrolysis System, and the DELTA & A2000 Fiber Instruments. Mounted on the front of the instrument, this LCD screen displays temperature, time, and other functions during an...

This O-Ring Kit includes parts that do not swell when contacting high penetrating solvents. This kit is no longer available. However, the components of the X95 kit can be ordered individually as parts #5663 and # 5806 .

This switch turns power on and off to the instrument.

This probe is used to measure the temperature within the Extraction Vessel of an XT10/XT10I and an XT15/XT15I.

This filter is used in the water supply line of the XT10/XT10I and XT15/XT15I.

The valve seat is attached to the end of the valve piston within the solenoid supply valve used on the XT10/XT10I, XT15/XT15I, HCl/HClI, DELTA/DELTAI, A2000/A2000I, and TDF/TDFI instruments.

The Moisture Stop Weigh Pouch contains a desiccant packet which absorbs moisture within the zipper bag. It is used when cooling and weighing filter bags to avoid unwanted absorption of moisture in the dried samples which would skew results.

The Drip Tray is part of the Maintenance Alert Assembly and is used in the DELTA, A200, and A2000 instruments. It functions as a collector for a fluid leak around the agitator, diverting it away from the motor.

Used in the XT15/XT15I Instrument. This kit includes replacement pistons for the four solvent valves (Q4, Q5, Q6, and Q7).

This kit includes replacement pistons for the two solvent valves (Q5 and Q6).

Before ordering an XT10/XT10I Extractor Vessel, contact our Technical Services Department to confirm your instrument configuration.

This part is used to filter solvent vapors and should be replaced every 3 months or after 100 instrument operations. This part is only used in the XT15/XT15I instruments.

Before ordering an XT15/XT15I Extractor Vessel, contact our Technical Services Department to confirm your instrument configuration.

This Viton™ O-ring is used within the solenoid supply valves on the XT10/XT10I, XT15/XT15I, HCl/HClI, DELTA/DELTAI, A2000/A2000I, and TDF/TDFI instruments for proper sealing and replaces the valve body seal O-ring around the inside of the valve guide...

The Valve Spring is used inside the solenoid supply valves on the XT10/XT10I, XT15/XT15I, HCl/HClI, DELTA/DELTAI, A2000/A2000I, and TDF/TDFI instruments and is inserted inside the Valve Piston w/ Viton® Seal. Note: For XT10/XT10I and XT15/XT15I -...

The pneumatically operated Enzyme Pinch Valve-N.O. regulates the input of enzymes. Refer to Service Procedure Pinch Valve Replacement (Enzymes) (TS009) for installation instructions.

This is a replacement bottom tray for the bag suspender, which is found in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments.

Replacement quick-release connector used in the top of the alcohol, buffer, and water containers, as well as in the enzyme bracket.

The Tubing Seal, 3x8 mm is used within the RF1X Module to secure and seal the Pressure Sensor ( Part #: RF31 ) and Viton-Silicone Tube ( Part #: RF11 ) into their respective ports in the bottom of the module housing.

The DELTA06 Heating Band Assembly is used in the DELTAI and A2000I Fiber Instruments. It serves to heat the digestion vessel during operation and replaces a failed heating band.

The Vent Valve Assembly, DELTA is used to release pressure from the top of the vessel and allow for unhindered draining through the drain valve. The vent valve also connects to the vessel pressure sensor.

Used with Digestion Vessel Glass ( Part #: FLEX55 ) seal port.

Small O-ring located in Vessel Bottom Assembly ( Part #: FLEX54 ) on the bottom side.

Large O-ring located in the Vessel Bottom Assembly ( Part #: FLEX54 ) on the top, inside.

Located in Slide Valve (Part #: FLEX30) and Vent Valve ( Part #: FLEX32 ) assemblies.

Located in #FLEX30 Slide Valve and #FLEX32 Vent Valve assemblies Rev A.

This vent valve is used in the jar lid ( Part #: D2.5 ) for releasing pressure from the jars during digestion.

Used in mixer assembly. Located below the Digestion Oven behind the front access panel.

Located in Vessel Top inside the Digestion Oven.

Located in Column Top Assembly.

Used for globe vent valve. Located inside the cabinet left side panel.

Located in Vessel Top inside the Digestion Oven.

Located inside Evaporation Chamber.

Replacement Vent Bottle & Tube Assembly for XT15/XT15I. This includes SS tube with compression fitting, bottle cap, 500ml coated glass bottle, and 6 ft. of chemical resistant tubing.

The Stainless Steel Latch secures the RD1 or RD2 Filter to the ANKOM Rapid Dryer (RD/RDI). One is used on either side of the Rapid Dryer.

The H38 Internal Hose Replacement Kit includes all internal hoses for the HCl/HClI ANKOM Hydrolysis instruments as well as hose clamps and one 1/2" Barbed Tee fitting.

The Nitrogen Flowmeter is used to regulate nitrogen flow to FLEX instrument.