Resource Center

This 10amp fuse is used in 120v AC input to the HCl, XT10, XT15, and in both TDF and TDFI on the DC output lines from the power supply. Used to protect against power surges.

This probe is used to measure the temperature within the Extraction Vessel of an XT10/XT10I and an XT15/XT15I.

This kit and the accompanying process guide provide the parts and instructions to complete the Preventative Maintenance (PM) process for the standard ANKOM XT10 Fat Extractor. This should be completed annually for an instrument used daily or once...

This piston is used for high-penetrating solvents and is included in the X55 Kit (XT15/XT15I) and the X73 Kit (XT10/XT10I).

The On/Off/Heat/Rotate Power Switch is used on the following ANKOM instruments: XT10/XT10I, XT15/XT15I, HCl/HClI, RD/RDI, TDF/TDFI, D200/D200I, DELTA/DELTAI, A200/A200I, A2000/A2000I, FLEX/FLEXI. On the D200/D200I Daisy Incubator, this switch also...

This cup insert top seal should be used regardless of the solvent being run in the XT10/XT10I and XT15/XT15I instruments.

Used in both the XT10/XT10I and XT15/XT15I. This valve spring is for the Q5 solvent valve only. This spring should not be used in any other valve.

This relay monitors the heaters in the following ANKOM instruments: XT15, XT10, HCl. DELTA, and A2000.

This relay monitors the heaters in the following ANKOM instruments: XT15I, XT10I, HClI, DELTAI, and A2000I.

The Bag Weigh Holder is used to hold a filter bag open for easy insertion of the sample. This part is especially useful during the weighing process.

This Extraction Vessel seal should be used when running Pet Ether in your XT10/XT10I and XT15/XT15I.

Used within the Extraction Vessel of the XT10/XT10I and XT15/XT15I, this assembly includes a Cup Insert and a Wave Spring Bag Holder.

This is the internal computer that controls the XT10 Fat Extractor.

This kit includes replacement pistons for the two solvent valves (Q5 and Q6).

This kit and the accompanying process guide provide the parts and instructions to complete the Preventative Maintenance (PM) process for the high penetration ANKOM XT10 Fat Extractor. This should be completed annually for an instrument used daily or...

This 120/220 volt supply provides the correct power to the instrument electronics.

The LCD Screen Assembly is used in the XT10 and XT15 Fat Extractors, the HCl Hydrolysis System, and the DELTA & A2000 Fiber Instruments. Mounted on the front of the instrument, this LCD screen displays temperature, time, and other functions during an...

Before ordering an XT10/XT10I Extractor Vessel, contact our Technical Services Department to confirm your instrument configuration.

The Valve Piston w/Viton® Seat is used inside the solenoid supply valves on the XT10/XT10I, XT15/XT15I, HCl/HClI, DELTA/DELTAI, A2000/A2000I, and TDF/TDFI instruments and to replace a damaged, worn, or corroded component. DELTA: found in the Vent...

This part holds the filter bags within the Cup Insert of your XT10/XT10I and XT15/XT15I.

This is a replacement fuse for a 220v instrument.

This part is used for both XT10/XT10I and XT15/XT15I.

This kit is no longer available. However, the components of the X87 kit can be ordered individually as parts 969.5 and 5806. This O-Ring Kit includes an Extraction Vessel seal ( Part #: 969.5 ) and a Cup Insert Top seal ( Part #: 5806 ). Use this kit...

This filter is used in the water supply line of the XT10/XT10I and XT15/XT15I.

The Moisture Stop Weigh Pouch contains a desiccant packet which absorbs moisture within the zipper bag. It is used when cooling and weighing filter bags to avoid unwanted absorption of moisture in the dried samples which would skew results.

The Valve Spring is used inside the solenoid supply valves on the XT10/XT10I, XT15/XT15I, HCl/HClI, DELTA/DELTAI, A2000/A2000I, and TDF/TDFI instruments and is inserted inside the Valve Piston w/ Viton® Seal. Note: For XT10/XT10I and XT15/XT15I -...

Replacement locking Safety Valve Assembly for XT10/XT10I and XT15/XT15I. Refer to Service Procedure Valve Replacement (Safety) (XTS004) for installation instructions.

Wire brush for cleaning the bottom of the XT10/XT10I and XT15/XT15I vessel. If fat residues burn to the bottom of the vessel, this tool, when used with a drill, will assist with cleaning.

Used in both XT10/XT10I and XT15/XT15I. The X78 Flow Control Assembly is used to visually indicate that water is flowing through the reflux circuit during the reflux cycle. Once the solvent has reached extraction temperature, the reflux circuit will...

This PTFE washer is used to seal the brass solvent filter to prevent leaks in the XT10/XT10I and XT15/XT15I.

The XT Solvent Drain Valve Assembly is used in the XT15/XT15I and XT10/XT10I Fat extractors. Its function is to maintain pressure in the vessel within certain limits during the run and to drain the vessel at the end of the run.

This part is used for XT10/XT10I only.

This O-Ring Kit includes parts that do not swell when contacting high penetrating solvents. This kit is no longer available. However, the components of the X95 kit can be ordered individually as parts #5663 and # 5806 .

The valve seat is attached to the end of the valve piston within the solenoid supply valve used on the XT10/XT10I, XT15/XT15I, HCl/HClI, DELTA/DELTAI, A2000/A2000I, and TDF/TDFI instruments.

This Viton™ O-ring is used within the solenoid supply valves on the XT10/XT10I, XT15/XT15I, HCl/HClI, DELTA/DELTAI, A2000/A2000I, and TDF/TDFI instruments for proper sealing and replaces the valve body seal O-ring around the inside of the valve guide...

This gauge shows the amount of pressure within the XT10/XT10I and XT15/XT15I Extraction Vessel during instrument operation. Operating pressure will vary depending on the solvent being used.

A 5605 Clear Glass Bottle with protective coating is one of the bottle options that can be used with an RF1 Gas Production Module or used to collect solvent vented from the XT15 and XT10 Instruments. This bottle provides the following features: - up...

This Extraction Vessel seal should be used when running high penetrating solvents like Diethyl Ether in your XT10/XT10I and XT15/XT15I.

This solid state relay is used in the following ANKOM instruments: XT10/XT10I, XT15/XT15I, HCl/HClI, TDF/TDFI, DELTA/DELTAI, A2000/A2000I, FLEX/FLEXI. It is used to control power to the AC heaters.

Used in both the XT10/XT10I and XT15/XT15I. This metal screen filters particles and should be cleaned regularly. XT15 Service Procedure Instrument and Components Cleaning (X5S017) provides instructions for accessing this part.