Resource Center

Replacement quick-release connector insert used on the ends of the supply tubes, which connect into the top of the alcohol, buffer, and water containers. Please specify the color: Blue , Red , Green , or White .

This is a replacement upper tray for the bag suspender which is found in the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments. Eight of these are used in the bag suspender assembly.

This is a maintenance tool used to clean the (6) 0.020" (0.5mm) holes in the spray tip.

The Valve Piston w/Viton® Seat is used inside the solenoid supply valves on the XT10/XT10I, XT15/XT15I, HCl/HClI, DELTA/DELTAI, A2000/A2000I, and TDF/TDFI instruments and to replace a damaged, worn, or corroded component. DELTA: found in the Vent...

The Chemical Receptacle is used to house an NaOH (or stronger Base) when performing oxygen consumption studies. The function of the Base material is to scavenge the CO2 produced by the aerobic metabolism. This produces a negative pressure as the O2...

The RFI Filter 120v/220v is a power receptacle used on the DELTA/DELTAI, A200I, and A2000/A2000I. It is not used on the A200. It is located on the side of the instrument and connects the instrument to a power source through a removable power cord.

Useful in the AOAC 2009.01/2011.25 methods, this cup is used to capture the filtrate that comes through the SDF Filter Bag.

These lamps light the inside of the heat and agitate switches.

This quick disconnect fitting mounts onto either side of the upper enclosure of the A2000/A2000I Fiber Analyzers. The part is used to connect to the detergent solution cubitainers.

The replacement Hose Coupler is used on the DELTA/DELTAI, A200/A200I, and A2000/A2000I Fiber instruments. It connects to the drain hose at the side of the instrument. Includes 2 pieces.

The TDF120 In-Line heater Core is used to replace leaking brass tubing on the In-Line Heater. It includes connected silicone tubing for ease of installation. The heater cartridge and thermistor (temp sensor) are not included in this assembly.

The HCl Extraction Chamber must be sealed during an assay. The H2 Lid/Latch Assembly seals the Extraction Chamber in the HCl instrument. ​This assembly includes the latch that secures the lid to the instrument.

The HCl Extraction Chamber must be sealed during an assay. The H3 lid seals the Extraction Chamber in the HCl instrument. This assembly does not include the latch that secures the lid to the instrument.

The H37 Bag Holder is used to hold the bags in the HCl/HClI Extraction Chamber during as assay. This assembly holds 15 bags. Can also be used in the RD/RDI Dryers.

This bolt is used for securing the lid and hinge block assembly to the vessel.

Attaches on the top of the RD/RDI Dryer. This filter is used when drying filter bags before and after a fat extraction done with an ANKOM XT10/XT10I or an ANKOM XT15/XT15I Extractor.

The RF Gas Production System bottles that include a septa port use a 3 mm 2-sided PTFE coated Silicone Septa to provide an easy to penetrate seal while providing minimal pressure loss per penetration. The RF35 pack includes 10 septa.

The Glass Tip with O-ring is a part of the analog level sensing system in the DELTA/DELTAI, A2000/A2000I Fiber instruments. Found in the Fiber Optic Cable & Glass Tip assembly ( Part #: A32 ), it is used to detect and regulate the fill level within...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7057 bottle provides the following features: - up to 1000ml of space to hold analysis material - a protective coating...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7126 bottle provides the following features: - up to 100ml of space to hold analysis material - an Amber tint to...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7127 bottle provides the following features: - up to 250ml of space to hold analysis material - an Amber tint to...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7130 bottle provides the following features: - up to 250ml of space to hold analysis material - a protective coating...

ANKOM provides many different bottles that can be connected to an RF1 Gas Production Module within the RF Gas Production System. The 7132 bottle provides the following features: - up to 1000ml of space to hold analysis material - a protective coating...

The 7147 Male Luer Cap is used to close off the end of the Female Luer Port ( Part #: 7146 ) or the Luer Duckbill Check Valve ( Part #: 7139 ).

The Copper Water Supply is used to connect the DELTA/DELTAI and A2000/A2000I instruments to the user's water source.

The Tubing Seal, 3x8 mm is used within the RF1X module to secure and seal the Pressure Sensor ( Part #: RF31 ) and Viton-Silicone Tube ( Part #: RF11 ) into their respective ports in the bottom of the module housing.

Used for globe vent valve. Located inside the cabinet left side panel.

Located inside Evaporation Chamber.

This kit and the accompanying process guide provide the parts and instructions to complete the Preventative Maintenance (PM) process for the standard ANKOM XT15/XT15I Fat Extractor. This should be completed annually for an instrument used daily or...

This kit and the accompanying process guide provide the parts and instructions to complete the Preventative Maintenance (PM) process for the high penetration ANKOM XT10 Fat Extractor. This should be completed annually for an instrument used daily or...

For use in the ANKOM FLEX Analyte Extractor. High Strength PTFE magnetic stir-bar; used in each assembled digestion vessel for more difficult to mix samples.