Resource Center

Used in both the XT10/XT10I and XT15/XT15I. This metal screen filters particles and should be cleaned regularly. XT15 Service Procedure Instrument and Components Cleaning (X5S017) provides instructions for accessing this part.

This assembly includes the handle and clamping device used for sealing the lid and hinge block assembly to the vessel.

This motor agitates the bag suspender at the proper RPM in the A200, 120v instrument.

This motor agitates the bag suspender at the proper RPM in the A200I, 220v instrument.

This assembly heats the digestion vessel in the A200, 120v instrument.

The Process Pump is the fluid delivery pump used to deliver all reagents from the reservoirs to the vessels.

The Waste Bottle Assembly is used to capture waste from the FLEX instrument and includes the waste collection bottle, cap, and tubing.

The Flask Clip Assemblies are an adhesive-backed spring clip used to secure the round bottom flasks in position again the recovery door.

This connects power to the Paddle Bar.

The jars rotate on this roller.

Used in both the XT10/XT10I and XT15/XT15I. This valve spring is for the Q5 solvent valve only. This spring should not be used in any other valve.

This module cap includes a notch that allows for a battery extension cable.

This container is used to hold the Buffer for TDF CODEX methods.

This 90° Brass Elbow is found in the DELTA/DELTAI and A2000/A2000I Fiber instruments and connects the drain valve to the exhaust hose.

The Low Pressure Sensor Assembly is used to monitor nitrogen (N2) line pressure in two locations. One marked 43 monitors N2 going to the four round bottom flasks used for solvent evaporation. One marked 45 monitors N2 Low Pressure and is displayed on...

The High Pressure Sensor Assembly is used to monitor the main nitrogen input line pressure to the instrument.

The Vessel Low Pressure Sensor Assembly is used to monitor pressure in the four vessels during filling and saponification. Specify vessel 1, 2, 3 or 4 at checkout.

The Motor with 4-wire cable is a stepper motor which operates the vessels' magnetic stirrers.

The FLEX21 Thermistor Assemblies are used to monitor temperature at eight locations. One is used to monitor the vessels' temperatures and is marked 46. One is used to monitor the reference temperature surrounding the round bottom flasks and is marked...

The Optical Bubble Sensor Assemblies function as a drain sensor and monitor fluid lines at five locations. Four sensors are used to confirm drain of the vessels. Those used for vessels 1, 2, 3, and 4 are marked 31, 32, 33,34, respectively. One marked...

Belt 808 rides on this roller.

The Thermal Cut-off Assembly is used in the heater for the oven. It consists of a non-resettable thermal fuse that shuts down power to the heater if the temperature exceeds 240°C.

The FLEX24 High Temperature Thermistor Assembly is marked 56 and is used to monitor the temperature within the oven.

The Vent Valve Assembly functions to release pressure from the vessels during vessel fill and saponification.

The RF Gen 3 Circuit Board contains the electronics used for communication with all RF1X / RF5X modules.

The RF Solenoid assembly is used to replace a faulty solenoid pinch valve within the RF1 or RF1X Module.

The FLEX Maintenance Kit provides the essential items needed to keep your FLEX Analyte Extractor operating smoohtly. The following items are included: 4 - Container Filters ( Part #: 8202) 4 - Vessel Top O-Ring ( Part #: 9231) 4 - Column top O-Ring (...

This adapter lid with GL45 threads allows RF Modules to fit 1.8L wide mouth jar ( Part #: 7181).

This part displays the solvent level on the XT15/XT15I instruments.

Belt 808 rides on this roller.

Used only in the cleaning of the Vessel Tops at the end of the run for Fat analyses that use hydrochloric acid (HCl). Procedure for use is available in the FLEX Operator's Manual.

This tube replacement set is used as part of preventative maintenance and includes precut, bagged, and labeled lengths of silicone tubing (1/4”OD x 1/8”ID) used in the supply of reagents in the ANKOM TDF Dietary Fiber Analyzer.

This tube replacement set is used as part of preventative maintenance and includes pre-cut, bagged, and labeled lengths of silicone tubing (3/16”OD x 1/16”ID) used in the delivery of reagents in the ANKOM TDF Dietary Fiber Analyzer.

Used in older XT15/XT15I. Please contact ANKOM for more information.

The TDF129 kit provides all the tubing and parts necessary to perform the annual maintenance for a TDF instrument. This includes all the supply tubing, delivery tubing, enzyme tubing, and all related tubing plus several parts that can fatigue over...

The Amylase Dispenser connects to the DELTA/DELTAI instrument and is used as a reservoir to dispense amylase into the vessel for digestion of starch during a Neutral Detergent fiber analysis.

The DELTA01 Maintenance Alert Assembly is used in the DELTA and A2000 instruments. It includes the Drip Tray w/plugged drain hole ( Part #: 692), Agitator Apron ( Part #: 638.7), and brass washer and functions as a collector for a fluid leak...

This drive roller connects the motor to the drive pulleys.

The Vessel Bottom Plug is used during the Solution Delivery Calibration of the FLEX liquid pump. It is used to seal the bottom hole of the Vessel Bottom Assembly ( Part #: FLEX54).