Resource Center

Pneumatic Control Solenoid Valve used in TDF and FLEX Instruments. Replacement part for a faulty Solenoid Valve.

This is a 100 hr timer assembly for monitoring incubation times of samples in the ANKOM Daisy II Incubator (D200/D200I).

This relay monitors the heaters in the following ANKOM instruments: XT15, XT10, HCl. DELTA, and A2000.

Part #: A29 is not available for purchase on the web. For assistance, please contact ANKOM Technology.

The jars rest on these bumpers during digestion.

This larger 4 liter chemical container is used for supplying deionized water to the instrument. The larger size accommodates 8 runs on the instrument before refilling is necessary.

Replacement set of red light bulb and ceramic heater (50w/220v) for improved heating of D200i chamber. Sold as set only.

This larger 4 liter chemical container is used for supplying buffer to the instrument. The larger size accommodates 8 runs on the instrument before refilling is necessary.

This larger 4 liter chemical container is used for supplying EtOH78 to the instrument. The larger size accommodates 8 runs on the instrument before refilling is necessary.

This larger 10 liter chemical container is used for supplying EtOH95 to the instrument. The larger size accommodates 4 runs on the instrument before refilling is necessary.

This holder is used to position the HCl container in the appropriate location next to the instrument.

This holder is used to position the Distilled Water, Buffer, and 78% EtOH containers in the appropriate location next to the instrument.

This part protects the 120v instrument against power surges that are out-of-specification.

This part protects the 220v instrument against power surges that are out-of-specification.

This is the heater assembly in the 120v RD Dryer.

This is the heater assembly in the 220v RD Dryer.

This is the fan assembly in the 120v RD Dryer.

This drive belt connects the motor and the drive roller ( Part #: 834).

This is the fan assembly in the 220v RD Dryer.

The Open End Wrench 1-1/8" is used to tighten the Brass Packing Nut ( Part #: 640) found on the DELTA/DELTAI, A200/A200I, A2000/A2000I Fiber instruments.

This is the controller with display used in the 120v RD Dryer.

This is the controller with display used in the 220v RD Dryer.

Power Supply B is a transformer that supplies 25v DC power to the solenoid valves and paddle heaters. This comes with an in-line fuse kit for overload protection and is used for both 110v and 220v instruments.

The MUX-T board communicates temperature signals to the main controller and is critical in paddle and in-line heat control.

This 15 amp fuse is used on the DELTA, A2000, and A200, Fiber instruments (120v). It helps protect the instrument from a possible power surge.

This 10 amp fuse is used on the DELTAI and A2000I Fiber instruments (220v) along with RD (120v) and RDI (220v). It helps protect the instrument from a possible power surge.

During digestion, the jars ride on this belt to prevent them from slipping.

The Pump assembly is found in the DELTA/DELTAI Fiber instruments and includes a fill valve and pump to supply the vessel with chemicals and rinse water.

The Pressure Sensor Assembly is used in the DELTA & DELTAI Fiber instruments for measuring the initial pressure before a run. It also measures the pressure during a run to monitor the process and ensure proper extraction.

The Water Regulator Assembly is found in the DELTA/DELTAI Fiber instruments and helps maintain the appropriate water pressure for rinses and manifold flushing.

The Splat Controller w/ Spice Board is used in the DELTA Fiber instrument and holds the program, controlling all funtions of the DELTA instrument.

This is the High Pressure Regulator for the TDF instrument.

This is the Low Pressure Regulator for the TDF instrument.

The 7146 Female Luer Port is included as part of each RF module and used to connect the Luer Duckbill Check Valve ( Part #: 7139) to the RF module. This part can also accept the Male Luer Cap ( Part #: 7147) to close off the port.

For use in the ANKOM FLEX Analyte Extractor. Precision ground glass vessel with port and cap; used in the digestion step of the analysis. The port allows the addition of internal standards. A FLEX55 combined with a FLEX54 form a complete Digestion...

For use in the ANKOM FLEX Analyte Extractor. Virgin PTFE white vessel bottom assembly; used in the digestion step of the analysis. A FLEX54 combined with a FLEX55 form a complete Digestion Vessel Assembly.

This dual voltage fan drives air through the Daisy Incubator (D200/D200I) to maintain consistent heat.

For use in the ANKOM FLEX Analyte Extractor. Precision ground round bottom flask with a 34-15 taper ground joint; used in the evaporation step of the instrument.

The RF45X Programmed RF Chips with embedded antenna facilitate communication between the Gas Production Modules, the Module Zero, and the Gas Production Base Coordinator.

Individual replacement paddle for the ANKOM TDF paddle bar. Includes embedded temperature sensor and heater cartridge.

Power Supply A is a 10 amp transformer that supplies 24v DC power to the pump motor controller (PMC) and analog multiplexer boards MUX-T ( Part #: TDF111) and MUX-P ( Part #: TDF112). This supply is used for both 110v and 220v instruments.

The MUX-P board communicates pressure signals to the main controller and is critical in accurate pump tube test results, input pressure readings, and vacuum readings during each fluid delivery.

The RF2X Base Coordinator facilitates communication between the Gas Production Modules ( RF1X/ RF5X) and the GPM Software installed on a PC. One RF2X Base Coordinator services an RFS base kit of up to 50 modules. To purchase, please contact ANKOM...