Resource Center

Used in mixer assembly. Located below the Digestion Oven behind the front access panel.

Located in Vessel Top inside the Digestion Oven.

Located in Column Top Assembly.

Used for globe vent valve. Located inside the cabinet left side panel.

Located in Vessel Top inside the Digestion Oven.

Located inside Evaporation Chamber.

Replacement Vent Bottle & Tube Assembly for XT15/XT15I. This includes SS tube with compression fitting, bottle cap, 500ml coated glass bottle, and 6 ft. of chemical resistant tubing.

The Stainless Steel Latch secures the RD1 or RD2 Filter to the ANKOM Rapid Dryer (RD/RDI). One is used on either side of the Rapid Dryer.

The H38 Internal Hose Replacement Kit includes all internal hoses for the HCl/HClI ANKOM Hydrolysis instruments as well as hose clamps and one 1/2" Barbed Tee fitting.

The Nitrogen Flowmeter is used to regulate nitrogen flow to FLEX instrument.

This part protects the D200/D200I instruments against power surges that are out-of-specification.

This kit and the accompanying process guide provide the parts and the instructions to complete the Preventative Maintenance (PM) process for the DELTA or A2000 Automated Fiber Analyzers. This procedure should be completed annually for an instrument...

This kit and the accompanying process guide provide the parts and instructions to complete the Preventative Maintenance (PM) process for the standard ANKOM XT15/XT15I Fat Extractor. This should be completed annually for an instrument used daily or...

This kit and the accompanying process guide provide the parts and instructions to complete the Preventative Maintenance (PM) process for the high penetration ANKOM XT15/XT15I Fat Extractor. This should be completed annually for an instrument used...

This kit and the accompanying process guide provide the parts and instructions to complete the Preventative Maintenance (PM) process for the standard ANKOM XT10 Fat Extractor. This should be completed annually for an instrument used daily or once...

This kit and the accompanying process guide provide the parts and instructions to complete the Preventative Maintenance (PM) process for the high penetration ANKOM XT10 Fat Extractor. This should be completed annually for an instrument used daily or...

For an existing ANKOM TDF instrument, the TDF65 Codex Method Upgrade kit will be needed to run methods AOAC 2022.01, AOAC 2017.16, AOAC 2011.25, and AOAC 2009.01. This includes: TDF17 Control Panel with Codex method software functionality TDF57...

Used in the Column Nitrogen System, the FLEX45 includes four check valves, a 4-position manifold, an aluminum compression plate, tubing, and connection fittings.

For use in the ANKOM FLEX Analyte Extractor. High Strength PTFE magnetic stir-bar; used in each assembled digestion vessel for more difficult to mix samples.

This 120/220 volt supply provides the correct power to the instrument electronics.

This access panel is designed with a viewing window, allowing users to easily monitor their slide valve condition.

After the evaporation step is complete, this cap is placed on the round bottom flask immediately after removing it from the instrument. This is to preserve the inert atmosphere inside the flask.

These flexible diaphragms allow the sensors located in the vessel vent valve to accurately record vessel pressures, while simultaneously protecting them from any harmful solutions. Over time, these may need to be replaced due to wear. All four must...

The adhesive gasket (2.75ft length) is used on the rear B & D clamp bars to ensure a good seal of the IDF and SDF bags during digestions or the precipitation phase.

Volume calibration cups used for running the volume calibration on the TDF instrument. Sold as a set of 12 (6 spare cups and 6 calibration cups).

This Extraction Vessel seal should be used when running Pet Ether in your XT10/XT10I and XT15/XT15I.

The Water Hammer Arrestor absorbs the pressure spike within water lines that occurs when valves are suddenly closed. This minimizes the reverberation and resulting rattling of pipes and potential damage to fixtures & appliances. Mini Water Hammer...

This bag holder is used for drying fiber bags in RD/RDi and has 24 positions.

The DELTA08 Pump Tube Replacement Kit is used in the DELTA/DELTAI instrument and incudes a full set of chemical resistant tubing with hose clamps. This connects from the manifold, to the pump assembly and supplies all solutions to the vessel.